Daljinski za garazna vrata - kopirajuci na 433 MHz

53 pregleda
2 želi ovaj predmet

Daljinski za garazna vrata - kopirajuci na 433 MHz

Cena: 500 din.

Kupi odmah

Saznajte više o Limundo zaštiti

Prodavac

danijel.catic

(714)

100% pozitivnih ocena u poslednjih 12 meseci

906 pozitivnih ocena

Beograd-Palilula, Grad Beograd, Srbija

Svi predmeti prodavca

Detalji predmeta

  • Stanje Nekorišćeno

Daljinski za garazna vrata - kopirajuci na 433 MHz

Univerzalni klonirajuci daljinski za garazna vrata na 433 MHz.. kopira postojeci daljinski, ali samo sa fiksnim kodovima (ne moze da kopira plivajuce kodove).

Kopiranje se vrsi na sledeci nacin:

Prvo obrisati memoriju:
1. Istovremeno se pritisne i A i B i drzi dok led dioda ne zatreperi 3 puta
2. Jedno dugme se otpusti a drugo ostaje i dalje pritisnuto. Otpusteno dugme se pritisne 3 puta. Lampica treba da pocne brzo da treperi.
Memorija je obrisana.

3. Prinese se stari daljinski da dodirne novi.
4. Na novom se pritisne dugme na koje zelite da iskopirate kod. Na starom se pritisne dugme sa koga zelite da iskopirate kod.
6. Kada LED dioda na novom zatreperi tri puta, kopiranje je završeno.


Operating Frequency: 433(433.92)MHz
Rated Voltage: 3V
Size: 60 x 34 x 16mm
Weight: 30g

Note:
This product can copy the remote control with the following chip inside: 2260(all manufacturers); 2262(All manufacturers); PT2264, 5326(All manufacturers);SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014, SMC918 series, 527(All manufacturers); 1527(All manufacturers); 2240(All manufacturers); HCS101, HCS200HCS201(part code), HCS300HCS301(part code), part single chip microcomputer.
If you fail in copying with proper operation, you might have to check whether your device has a chip above.
HCS encryption chip and other encryption chip can not be copied.

How to Program:
Because the fob has code when it was produced, so you need to reset it before copying.
Reset:
Hold buttons A and B down simultaneously, once the LED is flashing continuously, release both buttons to complete the reset.(If your remote hasn't have button A or B, just press the top two buttons)
Copy:
Hold down the button on the original remote you want to copy while simultaneously pressing and holding which button you want to program on the new fob (A, B, C, D etc.).(Both your original remote and new remote’s head should close to each other)
The process will be complete with the fob LED flashes.
Tips:
If you reset the code that you had copied and want to recover, press buttons C and D (or the bottom two buttons) until LED light flashing.
Notice:
If done correctly, can use directly. If not, or individual button not useful, please turn to clean and copy again, notice the change of light during operation. If problems still exist after attempting several times, check the chip and frequency of original remote control again

Uslovi prodaje prodavca

  • Plaćanje Tekući račun (pre slanja), Pouzećem, Lično
  • Slanje Lično preuzimanje, Post express

Prodavac

danijel.catic (714)

100% pozitivnih ocena u poslednjih 12 meseci

906 pozitivnih ocena

Beograd-Palilula, Grad Beograd, Srbija

Svi predmeti prodavca
Predmet: 102963697